{"id":5211,"date":"2026-08-26T11:36:37","date_gmt":"2026-08-26T11:36:37","guid":{"rendered":"https:\/\/aboutfoundry.com\/tensile-strength\/"},"modified":"2026-08-26T13:28:45","modified_gmt":"2026-08-26T13:28:45","slug":"tensile-strength","status":"publish","type":"post","link":"https:\/\/aboutfoundry.com\/en\/tensile-strength\/","title":{"rendered":"Tensile Strength and Hardness: Conversion Approaches and Practical Solutions"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\"><strong>Tensile Strength and Hardness: Conversion Approaches and Practical Solutions<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The mechanical properties of castings are critical to their fitness for use. Tensile strength and hardness are among the most important characteristic values. But how are these values related, and when does a conversion between them make sense?<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Basics of the Relationship Between Hardness and Tensile Strength<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Between tensile strength (Rm) and hardness measurements there is an empirical relationship that can be approximated for many cast materials, such as <a href=\"https:\/\/aboutfoundry.com\/en\/cast-iron\/\">cast iron<\/a>, using specific formulas. This relationship is based on the fact that both properties depend on the microstructure of the material.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Conversion Formulas for Common Cast Materials<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Grey Cast Iron \/ Lamellar Graphite Iron (GJL)<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>For Brinell hardness (HB): Rm [N\/mm\u00b2] \u2248 (HB \u00d7 0.95) \u2212 33<\/li>\n<li>Application range: HB between 150 and 250<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Some grey cast iron variants, such as <a href=\"https:\/\/aboutfoundry.com\/en\/meehanite-cast-iron\/\">Meehanite cast iron<\/a>, fall within this GJL family and follow the same general hardness-to-tensile-strength relationship.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Ductile Iron \/ Nodular Graphite Iron (GJS)<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>For Brinell hardness (HB): Rm [N\/mm\u00b2] \u2248 (HB \u00d7 3.2)<\/li>\n<li>Application range: HB between 150 and 300<\/li>\n<li>For ferritic GJS: Rm [N\/mm\u00b2] \u2248 (HB \u00d7 3.0)<\/li>\n<li>For pearlitic GJS: Rm [N\/mm\u00b2] \u2248 (HB \u00d7 3.4)<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Ferritic microstructures of this kind are often produced through a heat treatment process, such as the one used for <a href=\"https:\/\/aboutfoundry.com\/en\/annealed-cast-iron\/\">annealed cast iron<\/a>.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Aluminum Casting Alloys<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>For Brinell hardness (HB): Rm [N\/mm\u00b2] \u2248 (HB \u00d7 3.5)<\/li>\n<li>For important alloys such as AlSi7Mg or AlSi10Mg<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Practical Application of the Conversion<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">When Is a Conversion Useful?<\/h3>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>Fast quality control<\/strong>: hardness measurements are less destructive and quicker to carry out than tensile tests<\/li>\n<li><strong>Series production<\/strong>: spot-checking of larger batches<\/li>\n<li><strong>Retrospective assessment<\/strong>: for components that are already installed<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">This is particularly relevant for wear-resistant grades such as <a href=\"https:\/\/aboutfoundry.com\/en\/ni-hard-cast-iron\/\">Ni-hard cast iron<\/a>, where hardness is a primary quality indicator and is checked frequently.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Limits of the Conversion to Consider<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The conversion formulas are empirical approximations<\/li>\n<li>Deviations of 5-10% are common and acceptable<\/li>\n<li>For safety-critical components, always carry out direct tensile tests<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Practical Solutions for Foundry Operations<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Developing Plant-Specific Correlation Curves<\/h3>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Carry out parallel measurements for typical material\/alloy combinations<\/li>\n<li>Create your own conversion tables for your specific casting processes<\/li>\n<li>Update this data regularly whenever processes change<\/li>\n<\/ol>\n\n\n\n<h3 class=\"wp-block-heading\">Digital Solutions for Quality Assurance<\/h3>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Implement automated measurement procedures in your production line<\/li>\n<li>Use software for direct conversion and statistical evaluation<\/li>\n<li>Integrate the measurement data into your QM system for trend analysis<\/li>\n<\/ol>\n\n\n\n<h2 class=\"wp-block-heading\">Conclusion<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Converting between hardness and tensile strength offers practical advantages in foundry work. With the correct material-specific formulas and an awareness of their limits, quality assurance can be organized efficiently. For precise results, it is advisable to develop plant-specific correlation curves based on your own measurement data.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently Asked Questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">How is tensile strength estimated from Brinell hardness for ductile iron?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">For ductile iron (GJS), tensile strength can be approximated as Rm [N\/mm\u00b2] \u2248 HB \u00d7 3.2, for a Brinell hardness range of 150 to 300. Ferritic GJS uses a factor of about 3.0, while pearlitic GJS uses a factor of about 3.4.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Why are hardness-to-tensile-strength conversions used in foundries?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Because hardness testing is faster and less destructive than tensile testing, it is well suited for fast quality control, spot-checking batches in series production, and assessing components that are already installed.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What is the typical accuracy of these conversion formulas?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The formulas are empirical approximations. Deviations of 5-10% between the converted value and the actually measured tensile strength are common and generally acceptable, but safety-critical components should always be verified with a direct tensile test.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Related Standards<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Tensile testing of metallic materials, including cast materials, is generally carried out in accordance with DIN EN ISO 6892-1. Brinell hardness testing is standardized in DIN EN ISO 6506-1.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n","protected":false},"excerpt":{"rendered":"<p>Tensile Strength and Hardness: Conversion Approaches and Practical Solutions The mechanical properties of castings are critical to their fitness for use. Tensile strength and hardness are among the most important characteristic values. But how are these values related, and when does a conversion between them make sense? Basics of the Relationship Between Hardness and Tensile &hellip; <a href=\"https:\/\/aboutfoundry.com\/en\/tensile-strength\/\" class=\"more-link\">Continue reading <span class=\"screen-reader-text\">Tensile Strength and Hardness: Conversion Approaches and Practical Solutions<\/span><\/a><\/p>\n","protected":false},"author":4,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"inline_featured_image":false,"footnotes":""},"categories":[1],"tags":[],"class_list":["post-5211","post","type-post","status-publish","format-standard","hentry","category-unkategorisiert"],"acf":[],"_links":{"self":[{"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/posts\/5211","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/comments?post=5211"}],"version-history":[{"count":1,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/posts\/5211\/revisions"}],"predecessor-version":[{"id":5455,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/posts\/5211\/revisions\/5455"}],"wp:attachment":[{"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/media?parent=5211"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/categories?post=5211"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/aboutfoundry.com\/en\/wp-json\/wp\/v2\/tags?post=5211"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}